/**
   * Converts the given ThreadPoolExecutor into an ExecutorService that exits when the application
   * is complete. It does so by using daemon threads and adding a shutdown hook to wait for their
   * completion.
   *
   * <p>This is mainly for fixed thread pools. See {@link Executors#newFixedThreadPool(int)}.
   *
   * @param executor the executor to modify to make sure it exits when the application is finished

   * minimize unnecessary signals. One simple and correct algorithm is to signal some other waiter
   * with a satisfied guard (if one exists) whenever any thread occupying the monitor exits the
   * monitor, either by unlocking all of its held locks, or by starting to wait for a guard. This
   * includes exceptional exits, so all control paths involving signalling must be protected by a
   * finally block.
   *

	// Exit conditions:
	//
	// 1. If a writer.write() returns false, select loop below exits and
	// closes `doneCh` to indicate to caller to also exit.
	//
	// 2. If caller (Evaluate()) has an error, it sends an error
	// message and waits for this go-routine to quit in
	// FinishWithError()
	//
	// 3. If caller is done, it waits for this go-routine to exit
	// in Finish()

 *         }
 *         public void failure(Service service) {
 *           // Something failed, at this point we could log it, notify a load balancer, or take
 *           // some other action.  For now we will just exit.
 *           System.exit(1);
 *         }
 *       },
 *       MoreExecutors.directExecutor());
 *
 *     Runtime.getRuntime().addShutdownHook(new Thread() {
 *       public void run() {

	t.msg = "hello, world"
	g = t
}

func main() {
	go setup()
	for g == nil {
	}
	print(g.msg)
}
</pre>

<p>
Even if <code>main</code> observes <code>g != nil</code> and exits its loop,
there is no guarantee that it will observe the initialized
value for <code>g.msg</code>.
</p>

<p>
In all these examples, the solution is the same:
use explicit synchronization.
</p>

PURGE=$3 VERSIONING=$4 OBJECTLOCKING=$5 # Purge the bucket, if set & exists # Since PURGE is user input, check explicitly for `true` if [ $PURGE = true ]; then if checkBucketExists $BUCKET ; then echo "Purging bucket '$BUCKET'." set +e ; # don't exit if this fails ${MC} rm -r --force myminio/$BUCKET set -e ; # reset `e` as active else echo "Bucket '$BUCKET' does not exist, skipping purge." fi fi # Create the bucket if it does not exist and set objectlocking if enabled (NOTE: versioning will be not changed...

PURGE=$3 VERSIONING=$4 OBJECTLOCKING=$5 # Purge the bucket, if set & exists # Since PURGE is user input, check explicitly for `true` if [ $PURGE = true ]; then if checkBucketExists $BUCKET ; then echo "Purging bucket '$BUCKET'." set +e ; # don't exit if this fails ${MC} rm -r --force myminio/$BUCKET set -e ; # reset `e` as active else echo "Bucket '$BUCKET' does not exist, skipping purge." fi fi # Create the bucket if it does not exist and set objectlocking if enabled (NOTE: versioning will be not changed...

PURGE=$3 VERSIONING=$4 OBJECTLOCKING=$5 # Purge the bucket, if set & exists # Since PURGE is user input, check explicitly for `true` if [ $PURGE = true ]; then if checkBucketExists $BUCKET ; then echo "Purging bucket '$BUCKET'." set +e ; # don't exit if this fails ${MC} rm -r --force myminio/$BUCKET set -e ; # reset `e` as active else echo "Bucket '$BUCKET' does not exist, skipping purge." fi fi # Create the bucket if it does not exist and set objectlocking if enabled (NOTE: versioning will be not changed...

PURGE=$3 VERSIONING=$4 OBJECTLOCKING=$5 # Purge the bucket, if set & exists # Since PURGE is user input, check explicitly for `true` if [ $PURGE = true ]; then if checkBucketExists $BUCKET ; then echo "Purging bucket '$BUCKET'." set +e ; # don't exit if this fails ${MC} rm -r --force myminio/$BUCKET set -e ; # reset `e` as active else echo "Bucket '$BUCKET' does not exist, skipping purge." fi fi # Create the bucket if it does not exist and set objectlocking if enabled (NOTE: versioning will be not changed...

PURGE=$3 VERSIONING=$4 OBJECTLOCKING=$5 # Purge the bucket, if set & exists # Since PURGE is user input, check explicitly for `true` if [ $PURGE = true ]; then if checkBucketExists $BUCKET ; then echo "Purging bucket '$BUCKET'." set +e ; # don't exit if this fails ${MC} rm -r --force myminio/$BUCKET set -e ; # reset `e` as active else echo "Bucket '$BUCKET' does not exist, skipping purge." fi fi # Create the bucket if it does not exist and set objectlocking if enabled (NOTE: versioning will be not changed...