return msgp.NilSize
	}
	sz := msgp.ArrayHeaderSize
	for _, v := range j.val {
		sz += v.Msgsize()
	}
	return sz
}

// Value returns the underlying value.
// Regular append mechanics should be observed.
// If no value has been set yet, a new array is created.
func (j *Array[T]) Value() []T {
	if j.val == nil {
		j.val = j.p.newA(10)
	}
	return j.val
}

// Append a value to the underlying array.

      }
    }
    int oldValue = existingCounter.get();
    if (oldValue == expectedOldCount) {
      if (oldValue == 0) {
        if (newCount == 0) {
          // Just observed a 0; try to remove the entry to clean up the map
          countMap.remove(element, existingCounter);
          return true;
        } else {
          AtomicInteger newCounter = new AtomicInteger(newCount);

    Typically this would cause certain redirects to fail in debug and development configurations.


## Version 4.4.0

_2020-02-17_

 *  New: Support `canceled()` as an event that can be observed by `EventListener`. This should be
    useful for splitting out canceled calls in metrics.

 *  New: Publish a [bill of materials (BOM)][bom] for OkHttp. Depend on this from Gradle or Maven to

        }
      } finally {
        monitor.leave();
      }
    }

    /**
     * Marks the {@link State} as ready to receive transitions. Returns true if no transitions have
     * been observed yet.
     */
    void markReady() {
      monitor.enter();
      try {
        if (!transitioned) {
          // nothing has transitioned since construction, good.
          ready = true;
        } else {

      }

      return value;
    }

    /**
     * Performs routine cleanup following a read. Normally cleanup happens during writes, or from
     * the cleanupExecutor. If cleanup is not observed after a sufficient number of reads, try
     * cleaning up from the read thread.
     */
    void postReadCleanup() {
      if ((readCount.incrementAndGet() & DRAIN_THRESHOLD) == 0) {
        runCleanup();

      }

      return value;
    }

    /**
     * Performs routine cleanup following a read. Normally cleanup happens during writes, or from
     * the cleanupExecutor. If cleanup is not observed after a sufficient number of reads, try
     * cleaning up from the read thread.
     */
    void postReadCleanup() {
      if ((readCount.incrementAndGet() & DRAIN_THRESHOLD) == 0) {
        runCleanup();

can be tested. This section summarizes what one needs to take into consideration so that
tests won't fail when run in fips mode.

=== Muting tests in FIPS 140-2 mode

If the following limitations cannot be observed, or there is a need to actually test some use
case that is not available/allowed in fips mode, the test can be muted. For unit tests or Java
rest tests one can use

------------------------------------------------

 *   <dt>An IPv6 "IPv4 mapped" address, {@code "::ffff:192.168.0.1"}.
 *   <dd>{@code 00 00 00 00 00 00 00 00 00 00 ff ff c0 a8 00 01}
 * </dl>
 *
 * <p>A few notes about IPv6 "IPv4 mapped" addresses and their observed use in Java.
 *
 * <p>"IPv4 mapped" addresses were originally a representation of IPv4 addresses for use on an IPv6
 * socket that could receive both IPv4 and IPv6 connections (by disabling the {@code IPV6_V6ONLY}

	// the open file descriptor.
	//
	// Failing to check the return value when closing a file may lead to silent loss of data.
	// This can especially be observed with NFS and with disk quota.
	return w.Close()
}

// writeAllMeta - writes all metadata to a temp file and then links it to the final destination.

   * table is internally partitioned to try to permit the indicated number of concurrent updates
   * without contention. Because assignment of entries to these partitions is not necessarily
   * uniform, the actual concurrency observed may vary. Ideally, you should choose a value to
   * accommodate as many threads as will ever concurrently modify the table. Using a significantly